This paper presents the results of a study of the nature of lifting the tail lift of a truck with a hydraulic drive that supplies the working fluid to the cylinders in series for two positions of the center of gravity of the load on the lifting platform. A diagram of a hydraulic drive is presented, which supplies the working fluid to the hydraulic cylinders in series. Mathematical models describing the operation of the hydraulic drive are compiled according to the scheme. Simulation modeling was carried out using the MATLAB Simulink environment.

Keywords: wheel tyre, suspension module, wheeled vehicle, MATLAB Simulink, mathematical model, modeling

Based on the results of engineering and geological survey of real construction sites in Rostov-on-Don and the Republic of Kalmykia, the dynamics of subsidence processes on laboratory samples of loess soil tested for compression according to the "one curve" scheme according to GOST 23161-2012 was studied.

Keywords: subsidence, compression compression, odometer, loess soil, subsidence pressure, surveys, geomechanics, soil mechanics

This article discusses the problem of increasing the load-bearing capacity of bored piles. The technology of injecting fixing solutions into the ground under the foundations of a two-story building in the city of Azov to increase the load-bearing capacity of bored piles was described.

Keywords: structurally unstable soil, pile Foundation, load-bearing capacity, soil consolidation, silicatization, camouflage broadening, driving piles, bored piles, screw drilling, concreting

The search for the most efficient and cost-effective materials and structures is an important and urgent task. Reducing steel consumption can significantly affect the cost of structures, and the use of high-strength steel is one such method. Currently, there is great interest in reinforced concrete structures, which contain various combinations of pre-compressed, pre-tensioned and non-tensioned reinforcement. To determine the dependence of the bearing capacity on the class of concrete using the example of flexible reinforced concrete columns with combined reinforcement, a numerical experiment was performed. The performed numerical experiment showed the feasibility of using combined reinforcement - all the racks considered in the experiment with combined reinforcement are more effective than racks with non-tensioned reinforcement. At the same time, depending on the relative eccentricity of external forces and flexibility, it is necessary to choose the most effective type of combined reinforcement.

Keywords: column, combined reinforcement, prestressing, flexibility, reinforced concrete

The work has formulated a justification for the necessity to perform works aimed at solving the tasks of providing technological preparation of composite structures production by means of automation based on the application of modern information and computing systems. The characteristics and key aspects that determine the efficiency of automation at the stage of technological preparation of production are highlighted. Justification of the relationship between the processes determining the process formation and its efficiency is given

Keywords: automation, technological process, technological preparation of production, composite materials, composite designs, neural networks, modeling, process parameters

The basic principles of methodological support for the process of automation of technological preparation of production of products are formulated from the position of identifying the relationship of technological parameters of processing with the target properties of the product. The architecture of the neural network model is proposed and the basic principles of its construction are formulated.

Keywords: automation, technological process, technological preparation of production, neural networks, modeling, technological parameters, target properties

This article is dedicated to the research of existing methods of analysis and detection of persons in natural conditions. Face recognition based on image analysis is one of the main problems in the implementation of computer vision. The systems of reference measurements allow to define and develop various methods of face detection. Practical experiments were conducted and the algorithms for recognizing faces presented by scientific schools and commercial developments were considered, and also the results of evaluations on all test sets were analyzed based on the data of graphs of truly positive values for assessing the quality and speed of using MALF. Using a detailed assessment, the effectiveness of algorithms in various aspects with respect to several attributes was analyzed. Comparing performance with varying degrees of accuracy, the advantages and disadvantages of algorithms are determined when used in various work scenarios.

Keywords: computer vision, face detection, face detection, face recognition, image analysis algorithms, detection methods, reference measurements

The article describes and analyzes how to determine the thermal residual stresses. The conclusion, based on the analysis, showed the necessity of the calculation method for determining the residual stresses, which is based on a mathematical model of the formation of residual stresses and deformations occurring during heat treatment. The results of calculation of stresses and comparison with experimental data are given.

Keywords: residual thermal stresses, finite element method, heat treatment, low-hard details

snowmelter item, thawing, heat balance, thermal conductivity, the intensification of the phase transition.

Keywords: snowmelter item, thawing, heat balance, thermal conductivity, the intensification of the phase transition.

The composite cathode material of the core@shell type with the LiMn2O4@LiCoO2 formula of has been successfully synthesized using the solid-state reactions in several stages. Its structure has been studied by means of X-ray diffraction, scanning and transmission electron microscopy and vibrational infrared spectroscopy. Electrochemical investigation in two-electrode cell has been showed improvement of characteristics of the synthesized cathode material than the constituent components. The specific power of LiMn2O4@LiCoO2 is 650 mWh/g, against 450 and 500 mWh/g for LiCoO2 and LiMn2O4, respectively.

Keywords: lithium-ion batteries, cathode materials, Delafosse, X-ray structural analysis, electron microscopy, electrochemical properties

The solid solution of  LiMn1/3Cr1/3Fe1/3O2 with the structure of α-NaFeO2  isostructural with the widely used LiCoO2  has been synthesized and investigated as a cathode material. Rated voltage of LiMn1/3Cr1/3Fe1/3O2  relative to the lithium is 4 V.  The possibility of charging − discharging the material to a specific capacity of 220-250 mAh/g at currents of C/15-C/50 without phase transformations has been experimentally demonstrated. 

Keywords: lithium-ion batteries, cathode materials, Delafosse, solid solution, X-ray structural analysis, electrochemical properties

Is presented the solution of important sectoral issues to improve traffic safety of rolling stock by reducing lateral wear of wheels and rails heads when changes trucks in curves parts of the route by increasing reliability and durability of the pivot site.
To resolve this task, the paper proposed to the original design decision metered supply of lubricant to the friction surfaces of the parts with wear and tear their contact surfaces. According to the proposed resolution on friction surfaces pivot site are hollow, filled with solid composite lubricant, which in process of deterioration will portions get in contact area.
Theoretical foundations and the equation of adaptive management is present.

Keywords: center plate, adaptive regulator, operating parameters, lubricating layer, wear

In this paper we propose basic geometric, mass and electrical parameters of the element for collection of static electricity from the surface of the textile. This element is a reversible electrochemical charge storage system based on nanostructured nickel oxide and carbon cloth. Element has a planar structure, it is flexible, lightweight, safety and ergonomic. Proposed element can be used as a power source for the Microsystems technique in "smart clothes".

Keywords: "smart clothes", microsystems technique, static electricity, supercapacitor, composite material NiO/C

The intense strained state analysis results of the ""Kirovets"" KPP-16(20) portal crane trunk solid-state model are given in this work by a finite element method. Model operation of certainly element model in the program environment the Compass 3D v.14 is executed and results of its calculation in the form of the card of tension and the time-temperature chart for two cases of a loading are presented.

Keywords: finite element method, solid-state model, metal construction, portal crane, trunk, card of tension, time-temperature chart.

This paper considers the technological scheme of production of works at construction of control panel unit №2, Berezovsk Krasnoyarsk region. The selection of the necessary construction equipment.

Keywords: Justification of the choice of schemes for the complex mechanization of works in construction control panel unit №2, Berezovsk, Krasnoyarsk region